![Xenyx Xenyx](/uploads/1/1/8/6/118662545/798180369.jpg)
- Usb Driver Download Windows 10
- Behringer 302usb Driver
- Behringer Xenyx Q502usb Driver Download
- Behringer Xenyx 302 Usb Driver Download Mac Free
I got this little Behringer Xenyx 302USB mixer and wanted to run my guitar through some effects in Native Instruments Guitar Rig 5 (Guitar Rig 5 Player free download) and listen through headphones connected to the mixer.
Dec 15, 2010 The Xenyx series are mixers. They are not audio interfaces. Mixers merge audio signals together. So if you've got a microphone, plus a couple of other devices and you want their output combined so you can go to the same set of speakers (or something like that), that's where you'd use a mixer. Behringer Xenyx 302USB, Mac, and Guitar Rig 5 Leave a comment I got this little Behringer Xenyx 302USB mixer and wanted to run my guitar through some effects in Native Instruments Guitar Rig 5 ( Guitar Rig 5 Player free download ) and listen through headphones connected to the mixer.
When it comes to drivers and multimedia software, Macs are generally pretty easy to set up, but I had a bit of a hard time getting this to work. I didn’t find any single site with a complete solution, so maybe this post will help someone.
The problem: the device driver seemed to be working (USB Audio CODEC was showing in System Preferences and the meter in the input tab was lighting up when there was audio input), but there was no sound and Guitar Rig was not showing any signal at all.
My mixer is set up as shown here:
- guitar connected to the mixer’s mic in (XLR/1/4″ combo jack)
- under line/USB, FROM is in the DOWN position (USB Play)
- under line/USB, TO is in the DOWN position (Phones)
- mixer’s USB port connected to Macbook USB
I came across this article that suggested there could be a compatibility problem between the mixer and the Mac, but that it could be resolved by using Audio MIDI Setup to create an aggregate driver.
I followed those instructions. The result looks something like this (the USEME USB Audio CODEC):
Usb Driver Download Windows 10
(In the screenshot, note Drift Correction is only enabled on the input driver, but it should be enabled on the output driver as well.)
Next, I had to go in System Preferences and select the aggregate device for both input and output.
Finally, I also had to select the new aggregate device in Guitar Rig (File -> Audio and MIDI Settings).
After this, I just played around with enabling and disabling the left and right input channels in Guitar Rig and voilà. The IN and OUT meters showed a signal and, after tweaking knobs a bit, had sound too.
Behringer 302usb Driver
One final note: if you usually just close the cover of your MacBook, things may no longer work when you open it again. You may need to restart Guitar Rig and/or physically reconnect the mixer to get it working again. Good luck!
Behringer Xenyx Q502usb Driver Download
Should there be an installation disc with the XENYX 302, or do I even need to download anything else? (Jeff T. From France)
No, there is no installation disc included with the Xenxy 302 USB mixer from Behringer. Â The good thing about the 302 USB is it really doesn’t need drivers. Â You just plug it in and go. Â Your computer will recognize it as an audio device, or more specifically a secondary sound card titled “USB Audio Codec.” Â You can then set it as your recording device in either Windows itself or your recording software. Â You can also set it as your default playback device and run audio out through it if you wish.
No, there is no installation disc included with the Xenxy 302 USB mixer from Behringer. Â The good thing about the 302 USB is it really doesn’t need drivers. Â You just plug it in and go. Â Your computer will recognize it as an audio device, or more specifically a secondary sound card titled “USB Audio Codec.” Â You can then set it as your recording device in either Windows itself or your recording software. Â You can also set it as your default playback device and run audio out through it if you wish.
Behringer Xenyx 302 Usb Driver Download Mac Free
Behringer does offer downloadable “low-latency ASIO” drivers for all its USB-equipped Xenyx models on its website.  This may be required in some more complicated situations or higher-end models, but I find the 302 USB works just fine without it.